Hellobox Smart S2 is a new gadget just release couple of days ago
that give access to watch satellite tv channels through mobile phone
specifically on Android platform while iOS will soon join.
Hello Smart S2 has two major functions which is (1) Support Satellite
Finder through Bluetooth just like the accent Hellobox B1 Satellite
Finder and (2) To Watch Satellite Tv Channels via Streaming i.e it
requires internet connections to work either through wifi or LAN
Hello Smart S2 also working with DVBPlayer for easy streaming through Android Phone and Tablet, DVBPlayer App are available for download DVBPlayer App on Google PlayStore, DVBPlayer also support almost audio/video output, pretty graphic interface and as well as easy navigation.
For those that have interest to buy Hellobox Smart S2, You can place your order on aliexpress
How To Setup Hellobox Smart S2 with DVBPlayer To Watch Satellite tv Channels:
- After You download from the link provided above.
- You can Proceed to install the App.
- After Successfull Installation, Don’t Open the App yet.
- Now Connect Your Satellite tv Cable to your Smart S2 box.
- Connect the Power adapter to the wall socket and to the Smart 2 box.
- Now Open the DVBPlayer App, make sure you click on the icon at the top right hand corner (If you are using it for the first time) and wait for few seconds for the DVBPlayer to search for the nearest Smart S2 box.
- Once it get availabe connection like this “Box1 78:9C:E7:*****, Click or tap on this available device and wait for the new window to pop up
- Click or tap on Password and enter your wifi password.
- Click on Wifi Config and wait for few seconds to load and display propmt message ” No Channel, do you want to search channels? Yes or No“
- Then You are connected
How To Scan Channels on Hellobox Smart 2
If you are using it for the first time, please continue from the above steps by tap or click on “Yes” and it will automatically display Satellite tv Installation Settings,
- or Go Back to the main Menu and tap or click on “Settting icon“.
- Select your Prefered Satellite Name.
- Check the LNB Freqeuncy if it corresponding with LNB type.
- Make sure you setup your diseqc switch accoedingly (If you have more than one dish Connected to the diseqc switch) otherwise proceed.
- To Search Channels and click on it, and Choose Blind scan
- Wait For few minute to complete Scanning
- Then, If You are able to get some Channels then, You are good go otherwise Check your connections and settings and retry again.
- If You still get confuse, You can watch this video below
Hellobox Smart S2 Specification
- Exclusive Furrad® stream media interface.
- DVB Stream Media Interface Processor K7
- High-speed, Low power consumption 1Gb DDR memory Embedded.
- 32-bit RISC CPU integrates 16Kbytes I cache and 16Kbytes D cache.
- Embedded 802.11 b/g/n 150Mbps WiFi module.
- Integrates QPSK/8PSK/16APSK/32APSK DVB-S/DVB-S2 demodulator and FEC.
- DVB-S/S2 input 950~2150MHz, Level -65~-25dBm
- High performance dual-ADC with 10bits, up to 125MHz.
- High-speed searching mode for blind symbol rate acquisition.
- Supports 32 PIDs filtering with 16Bytes filter depth of each one.
- USB2.0 Host integrated, High-speed and Full-speed devices supported.
- USB2.0 port for external RJ45 Ethernet.
- Support online firmware upgrading.
- Embedded Bluetooth BLE 4.0 module.
- Power Input: DC5V 2.4A.
- Dynamic power consumption range 3~6W.
- Specially optimized Linux Operation System.
- Dynamic A/V buffer management algorithm for High Definition.
- Biss and PwrVu fully autoroll.
- Support cccam, newcam,mgcam.
0 comments
Post a Comment